Simrad NX45 Especificaciones Pagina 7
- Pagina / 120
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Simrad NX40/45 Installation and Operation Manual 7
Overview1
1-1 Overview
The Simrad NX40/45 is a rugged, highly integrated
marine chartplotter and shnder. It is easy to use and
has a high resolution color display. Complex functions
can be performed with only a few key presses, taking the
hard work out of boating.
The available functions depend on the optional sensors
and instruments that are installed:
The Video window requires the NX40/45 to receive •
video from a compatible source, such as a camera.
Fuel functions require fuel sensors to be installed.•
SmartCraft engine functions require a SmartCraft •
system to be installed. For information on using
SmartCraft, see the SmartCraft Gateway Installation
and Operation Manual.
The NX40/45 can send data to other instruments, •
such as an autopilot, and receive data from other
instruments.
Radar functions require an optional Simrad radar •
system to be installed.
AIS functions require an optional AIS receiver to be •
installed.
For information on installation options.
This manual describes how to install and operate the
NX40/45. Special terms are explained in Appendix C. For
more information on this instrument and other Simrad
products, go to our website, www.simrad-yachting.com.
1-2 Cleaning and maintenance
The screen is covered by a proprietary anti-reection
coating. To avoid damage, clean the screen only with
a damp cloth and mild detergent when dirty or covered
in sea salt. Avoid abrasive cleaners, petrol or other
solvents. If a plug-in card gets dirty or wet, clean it with
a damp cloth or mild detergent.
Avoid walking on or jamming cables and connectors.
Place the cover over the display when the unit is turned
off.
- NX40/45 1
- NavStation 1
- Contents 3
- Overview1 7
- 1-3 Plug-in cards 8
- Removing the display unit 9
- Replacing the display unit 9
- Basic Operation2 10
- 2-4 Man overboard (MOB) 13
- 2-5 Alarms 13
- 2-7 The main windows 14
- 2-6 Simulate mode 14
- Simulate > Simulate > 14
- > More 15
- Red border 16
- Navigation: Chart3 19
- 3-2 Chart window 21
- 3-2-1 Chart modes 22
- 3-2-2 Latitude and longitude 22
- 3-5 Tracks and tracking 25
- 3-4 Projected course 25
- Video window4 26
- Navigation: Highway window5 27
- Navigation: Waypoints6 28
- Navigation: Routes7 31
- Satellites8 35
- 9-1 Using the unit 36
- 9-2 Interpreting the display 37
- Strength of echoes 37
- Frequency and cone width 38
- Bottom types 38
- When to use Mixed 40
- When to use 50/200 kHz 40
- 50 kHz display 41
- 200 kHz display 41
- Where to nd sh 42
- Fish arches 42
- 9-5 Range 43
- Range > 43
- Zoom range and offset 43
- 9-6 Gain and threshold 43
- The gain window 44
- Threshold 44
- Echosounder10 45
- 10-1-1 Extended history mode 46
- Bottom lock > On or Off 47
- 10-3 Echosounder split window 47
- Setting gain and threshold 48
- Fish recognition 48
- Bottom type 48
- Gauges window11 49
- Data window12 50
- Fuel functions and display13 51
- B - Part ll a tank 53
- Add fuel 53
- C - Removing fuel 53
- Set remaining 53
- Set Remaining menu to 53
- For Example 1 55
- 13-6 Fuel consumption curves 55
- 13-7 Calibration 58
- Fuel > Setup engines 58
- Calibrate and change 58
- Tides window14 59
- User card window15 60
- 16-1 Viewing AIS Vessels 62
- TCPA 15 min 63
- CPA 0.5 nm 63
- Safety msgs (rx) 64
- to turn SmartCraft Off 65
- or > to conrm 66
- to conrm 66
- 17-3-4 Trim indicator 68
- Radar 18 70
- 18-6-1 Changing the gain mode 72
- Adjust Radar > Gain Mode 72
- oating VRM/EBL 76
- from the center to give 77
- Setting up the NX40/4519 80
- 19-1 Setup > System 81
- 19-2 Setup > Chart 82
- If you select a map datum 83
- It should 83
- Set > 84
- General submenu 84
- Land submenu 85
- Other submenu 85
- 19-4 Setup > Radar 87
- Radar > Installation 90
- 19-5 Setup > GPS 91
- 19-6 Setup > Fuel 92
- 19-7 Setup > Track 93
- 19-8 Setup > AIS 94
- 19-11 Setup > Units 96
- 19-12 Setup > Comms 96
- 19-13 Setup > Calibrate 97
- Calibrate 97
- 19-14 Setup > Time 98
- 19-15 Setup > Favorites 99
- 19-16 Setup > Simulate 99
- Simulate 99
- Installation 20 100
- GA B C D E F 101
- Flush Mounting the NX40/45 102
- Bracket Mounting the NX40/45 103
- Installing an antenna 105
- Echosounder to 105
- 20-9 Installation: SmartCraft 106
- 20-10 Installation: Radar 107
- Power cable 108
- Specications21 109
- COMMUNICATIONS 110
- STANDARDS COMPLIANCE 110
- Simrad NX45 111
- Simrad NX40 111
- List of datums 112
- Troubleshooting22 113
- B-3 Fuel consumption problems 114
- Economy 114
- B-4 echosounder shnding 115
- B-5 Radar problems 116
- Navigation data24 118
- Compliance statements25 119
Relacionado con productos y manuales para Los sistemas de navegación para automóviles Simrad NX45
(100 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales